This post was last modified: 2024-12-07, 13:17 by Gunther.

Hi Gunther, hope you are fine.

First I´d like to congratulate you for your amazing software and work. Love it!

If I may, I would like to talk about the "Export Timestamp Subtitles". I use it a lot. The problem is that in Capcut it can´t directly use it since it has a lot of lines on the file. So I always have to open the timestamp files and manually edit it. What I mainly do is to remove the lines that uses the exact same date/time and change the frames that it is related.

I think that in this way you could probably use the file directly in a lot of video editors (not only on Premiere). So it is my only sugestion.

Anyway, congrats again! Amazing software! You just managed to make this new version is even better!

Fernando.

P.S. To better explain it, please take a look at the example below:

Code:

--------------------------------------------------------------------------
LRTimelapse Exported Timestamp Subtitles:
--------------------------------------------------------------------------
1
00:00:00,000 --> 00:00:00,033
2024-06-20 04:01

2
00:00:00,033 --> 00:00:00,066
2024-06-20 04:01

3
00:00:00,066 --> 00:00:00,099
2024-06-20 04:01

4
00:00:00,099 --> 00:00:00,133
2024-06-20 04:01

5
00:00:00,133 --> 00:00:00,166
2024-06-20 04:01

6
00:00:00,166 --> 00:00:00,199
2024-06-20 04:01

7
00:00:00,199 --> 00:00:00,233
2024-06-20 04:01

8
00:00:00,233 --> 00:00:00,266
2024-06-20 04:02

9
00:00:00,266 --> 00:00:00,299
2024-06-20 04:02

10
00:00:00,299 --> 00:00:00,333
2024-06-20 04:02

11
00:00:00,333 --> 00:00:00,366
2024-06-20 04:02

12
00:00:00,366 --> 00:00:00,399
2024-06-20 04:02

13
00:00:00,399 --> 00:00:00,433
2024-06-20 04:02

14
00:00:00,433 --> 00:00:00,466
2024-06-20 04:02

15
00:00:00,466 --> 00:00:00,499
2024-06-20 04:02

16
00:00:00,499 --> 00:00:00,533
2024-06-20 04:02

17
00:00:00,533 --> 00:00:00,566
2024-06-20 04:02

18
00:00:00,566 --> 00:00:00,599
2024-06-20 04:02

19
00:00:00,599 --> 00:00:00,633
2024-06-20 04:02

20
00:00:00,633 --> 00:00:00,666
2024-06-20 04:02

21
00:00:00,666 --> 00:00:00,699
2024-06-20 04:02

22
00:00:00,699 --> 00:00:00,733
2024-06-20 04:02

23
00:00:00,733 --> 00:00:00,766
2024-06-20 04:03

24
00:00:00,766 --> 00:00:00,799
2024-06-20 04:03

25
00:00:00,799 --> 00:00:00,833
2024-06-20 04:03

26
00:00:00,833 --> 00:00:00,866
2024-06-20 04:03

27
00:00:00,866 --> 00:00:00,899
2024-06-20 04:03

28
00:00:00,899 --> 00:00:00,933
2024-06-20 04:03

29
00:00:00,933 --> 00:00:00,966
2024-06-20 04:03

30
00:00:00,966 --> 00:00:00,999
2024-06-20 04:03

31
00:00:00,999 --> 00:00:01,033
2024-06-20 04:03

32
00:00:01,033 --> 00:00:01,066
2024-06-20 04:03

33
00:00:01,066 --> 00:00:01,099
2024-06-20 04:03

34
00:00:01,099 --> 00:00:01,133
2024-06-20 04:03

35
00:00:01,133 --> 00:00:01,166
2024-06-20 04:03

36
00:00:01,166 --> 00:00:01,199
2024-06-20 04:03

-------------------------------------------------------------------------------
Edited timestamp file
-------------------------------------------------------------------------------

1
00:00:00,000 --> 00:00:00,233
2024-06-20 04:01

2
00:00:00,233 --> 00:00:00,733
2024-06-20 04:02

3
00:00:00,733 --> 00:00:01,199
2024-06-20 04:03

In LRTimelapse 7.2 beta 2 you can change a setting in the config which would allow you to have less entries in the SRT file. See: https://forum.lrtimelapse.com/Thread-lrt...7-2-beta-2

From the release notes:

Added setting to config "renderTimeStampEveryNthFrame", default is 1.0, which means the timestamps are written into SRT files for every single frame. If you would like every 2nd, set 2.0 here etc. Setting the value to -1 will create the timestamp every second (considers the fps rate).

To edit the config:
- Launch LRTimelapse
- Hit Ctrl-Shift-E (on mac CMD-Shift-E), this will open an editor with the config.
- Close LRTimelapse (before editing the config).
- Edit the config, in your case change the value after: renderTimeStampEveryNthFrame to -1.
- Save the config
- Launch LRTimelapse.

let me know if that serves you.